• Feel free to contact us: Mobile: 0344 3813810
    • True-RMS 1000A AC/DC
    • Work in tight spots with the 18" iFlex current probe and measure up to 2500A AC
    • CAT III/IV Safety ratings
    • 3 years Warranty
    The Fluke 376 Clamp Meter offers improved performance perfect for a wide range of current measurement situations. With true-rms ac voltage and current measurements, the Fluke 376 can read up to 1000 V and 1000 A in both ac and dc modes with the fixed jaw. The Fluke 376 is part of Fluke’s new Clamp Meter line that includes: 381, 375, 374, 373 & 365. Replacing the Fluke 337 The Fluke 376 clamp meter is the direct replacement for the Fluke 337 clamp meter. The Fluke 376 includes all the features of the 337, but also includes:
    • CAT IV 600, CAT III 1000 V
    • iFlex 2500 A AC
    • 1000 V AC/DC
    • mV DC
    • 60 kΩ
    • 1000 μF
    What’s Included:
    • 18-inch iFlex flexible current probe – i2500-18
    • TL75 test leads
    • Coated instruction card
    • Safety information sheet
    • Soft carrying case
    • Two AA Alkaline batteries
  • Feel free to contact us: Mobile: 0344 3813810
    • CAT IV 600
    • CAT III 1000 V
    • 3 years Warranty
    The Fluke 376 Clamp Meter offers improved performance perfect for a wide range of current measurement situations. With true-rms ac voltage and current measurements, the Fluke 376 can read up to 1000 V and 1000 A in both ac and dc modes with the fixed jaw. The Fluke 376 is part of Fluke’s new Clamp Meter line that includes: 381, 375, 374, 373 & 365. Replacing the Fluke 337 The Fluke 376 clamp meter is the direct replacement for the Fluke 337 clamp meter. The Fluke 376 includes all the features of the 337, but also includes:
    • CAT IV 600, CAT III 1000 V
    • iFlex 2500 A AC
    • 1000 V AC/DC
    • mV DC
    • 60 kΩ
    • 1000 μF
    What’s Included:
    • 18-inch iFlex flexible current probe – i2500-18
    • TL75 test leads
    • Coated instruction card
    • Safety information sheet
    • Soft carrying case
    • Two AA Alkaline batteries
  • Feel free to contact us: Mobile: 0344 3813810
    • True-RMS
    • 600 A AC/DC
    • Works with iFlex flexible current probes
    • 3 years Warranty
    The Fluke 376 Clamp Meter offers improved performance perfect for a wide range of current measurement situations. With true-rms ac voltage and current measurements, the Fluke 376 can read up to 1000 V and 1000 A in both ac and dc modes with the fixed jaw. The Fluke 376 is part of Fluke’s new Clamp Meter line that includes: 381, 375, 374, 373 & 365. Replacing the Fluke 337 The Fluke 376 clamp meter is the direct replacement for the Fluke 337 clamp meter. The Fluke 376 includes all the features of the 337, but also includes:
    • CAT IV 600, CAT III 1000 V
    • iFlex 2500 A AC
    • 1000 V AC/DC
    • mV DC
    • 60 kΩ
    • 1000 μF
    What’s Included:
    • 18-inch iFlex flexible current probe – i2500-18
    • TL75 test leads
    • Coated instruction card
    • Safety information sheet
    • Soft carrying case
    • Two AA Alkaline batteries
  • Feel free to contact us: Mobile: 0344 3813810
    • Detachable Jaw clamp
    • Built in Flash/Torch light
    • 3 years Warranty
    The Fluke 376 Clamp Meter offers improved performance perfect for a wide range of current measurement situations. With true-rms ac voltage and current measurements, the Fluke 376 can read up to 1000 V and 1000 A in both ac and dc modes with the fixed jaw. The Fluke 376 is part of Fluke’s new Clamp Meter line that includes: 381, 375, 374, 373 & 365. Replacing the Fluke 337 The Fluke 376 clamp meter is the direct replacement for the Fluke 337 clamp meter. The Fluke 376 includes all the features of the 337, but also includes:
    • CAT IV 600, CAT III 1000 V
    • iFlex 2500 A AC
    • 1000 V AC/DC
    • mV DC
    • 60 kΩ
    • 1000 μF
    What’s Included:
    • 18-inch iFlex flexible current probe – i2500-18
    • TL75 test leads
    • Coated instruction card
    • Safety information sheet
    • Soft carrying case
    • Two AA Alkaline batteries
  • Feel free to contact us: Mobile: 0344 3813810
    • CAT III Rating 600v
    • Low Pass Filter
    • 3 years Warranty
    The Fluke 376 Clamp Meter offers improved performance perfect for a wide range of current measurement situations. With true-rms ac voltage and current measurements, the Fluke 376 can read up to 1000 V and 1000 A in both ac and dc modes with the fixed jaw. The Fluke 376 is part of Fluke’s new Clamp Meter line that includes: 381, 375, 374, 373 & 365. Replacing the Fluke 337 The Fluke 376 clamp meter is the direct replacement for the Fluke 337 clamp meter. The Fluke 376 includes all the features of the 337, but also includes:
    • CAT IV 600, CAT III 1000 V
    • iFlex 2500 A AC
    • 1000 V AC/DC
    • mV DC
    • 60 kΩ
    • 1000 μF
    What’s Included:
    • 18-inch iFlex flexible current probe – i2500-18
    • TL75 test leads
    • Coated instruction card
    • Safety information sheet
    • Soft carrying case
    • Two AA Alkaline batteries
     
  • Feel free to contact us: Mobile: 0344 3813810 The Fluke 360 leakage tester is a rugged and accurate solution for leakage current measurement. Ideally designed for non-invasive checks of insulation condition, the Fluke 360 leakage meter allows you to perform tests without powering down the installation or disconnecting equipment – saving you time, without compromising on quality or safety. The unique jaw design of the Fluke 360 AC Leakage Current Clamp Meter eliminates the influence of adjacent current conductors, and measure leakage current down to 1 µA for monitoring of insulation and makes it ideal for checking insulation of low-voltage circuits and electrical components..  The ergonomic design of the Fluke 360 ensures easy measuring.  The measuring clamp fits into tight spaces and the wide display angle clearly shows the measured value on the display after removing the clamp for the measured conductor. The Fluke 360 minimizes the effects of external magnetic fields, even at low currents. This allows you to perform accurate and reliable tests in today’s crowded electrical environments. The tough and high-quality jaw design of the Fluke 360 leakage tester guarantees high stability for long-term repeatability and durability. Why leakage current testing? Leakage currents can be an indicator of the effectiveness of insulation on conductors. High levels of leakage current may be present in circuits where either the insulation resistance is low, or electronic equipment with filters is used. Leakage currents can cause disruptions of the normal operation of equipment and installations. It is possible to locate the source of leakage currents by using the Fluke 360 leakage current clamp meter and taking methodical measurements throughout the installation. The big advantage of leakage current testing versus insulation testing is that the installation and equipment do not need to be powered down but can be done during normal operation. What’s Included:
    • Soft carrying pouch
    • Users manual in languages: English, French, Spanish, German, Italian, Portuguese, Simplified Chinese
  • Feel free to contact us: Mobile: 0344 3813810 Industrial plants and large facilities often have equipment and installations that draw greater than 1000 A. As with other current measurements, it is not practical to disconnect the equipment to make a series of current measurements. The ability to check that an expensive system has been installed correctly, troubleshoot large loads, and make accurate measurements on UPS and Variable Frequency drives with noisy loads is also essential. In industrial settings, compliance with NFPA 70E safety standards, while making measurements, is critical. Fluke has addressed this by designing this product to meet CAT IV 600 V and CAT III 1000 V ratings. Confidently take reliable readings with the Fluke 353 AC/DC True-rms Clamp Meter – the tool of choice for high-current clamp-on amp meter measurements up to 2000 A. The extra-wide jaw easily clamps around large conductors, typically found in high-current applications and the extra rugged design has an extra element of user protection when taking high-powered measurements. Accurate peak measurements can be taken using the in-rush current mode, ideal for motors and inductive loads. Applications: Industrial plants and facilities Building maintenance, e.g. universities, hospitals, large offices, correctional institutions Plant works, e.g. power, pharmaceutical, printing, automotive assembly Manufacturing and process facilities Refineries Steel mills and other metal manufacturing plants Large DC systems such as DC electroplating, or marine electrical systems What’s Included: Fluke C43 Soft Carrying Case 6 AA batteries Users manual 3 year warranty
  • Feel free to contact us: Mobile: 0344 3813810
    • Ideal for VSDs, UPS, lighting
    • AC/DC with low pass filter
    • Data logging records results
    • 2 Years Warranty
    The Fluke 345 Power Quality Clamp Meter is Fluke’s newest power quality analyzer and is an ideal meter for commissioning and troubleshooting modern electrical loads. The Fluke 345 combines a power quality analyzer, digital clamp meter, oscilloscope, and data logger in one. This combination of functions, coupled with high quality digital filtering, makes it ideal for working with variable frequency motor drives, high efficiency lighting, and other loads using switching electronics. With the bright color power meter display to analyze the harmonic spectrum, a low-pass filter to remove high frequency noise, and a high EMC immunity design, the Fluke 345 power analyzer is ideal for measurements on switching loads such as variable speed drives, electronic lighting and UPS systems. Of course, the Fluke 345 is easy to use and will make the basic measurements of voltage and current to determine if there is something seriously wrong with the circuit under test. It’s rated for use at the service entrance with a 600 Volt CAT IV rating. With the 2000 A range and large jaw opening, you can evaluate most of the circuits in the building. The Fluke 345 can also measure both ac and dc voltage and current simultaneously, and identify the magnitude of each separately and combined as ac+dc true-rms. The Fluke 345 Power Quality Clamp Meter is the ideal tool for technicians and engineer involved in installing and commission switch electronic loads. It can deal with the difficult demands of measuring and monitoring variable frequency drives, UPS systems and other switching loads. It’s simply the ideal meter for commissioning and troubleshooting modern electrical loads. Additionally, the Hall Effect measurement system design makes measurement of dc current possible without the need to break the circuit with the power meter and the internal memory enables long-term logging for analysis of trends or intermittent problems. Applications: Setup and troubleshoot variable frequency drives and UPS systems – Verify correct operation by measuring key power quality parameters Harmonics measurements – Uncover harmonic issues that can damage or disrupt critical equipment Inrush capture – Check start-up current where spurious resets or nuisance circuit breaker tripping occurs Load studies – Verify electrical system capacity before adding loads What’s Included: 345 Power Quality Clamp Meter Soft carrying case Power Log software Test leads Alligator clips Test probes USB cable International ac adapter / battery eliminator Printed English language user manual Multi-language manual CD
  • Feel free to contact us: Mobile: 0344 3813810
    • Auto Power Off
    • Weight 230 g (8oz)
    • 2 Years Warranty
    Measure inrush motor starting current the way a circuit breaker sees it! Now everyone on your crew can have a Fluke Clamp Meter. This new smaller sized model offers accurate low current measurements, continuity test function and Fluke reliability. The Fluke 321 is designed to verify the presence of load current, AC voltage and continuity of circuits, switches, fuses and contacts. This small and rugged clamp meters are ideally suited for current measurements up to 400 A in tight cable compartments. This affordable instrument combine a compact package with a strong feature set: New smaller size fits easily into tight places Precise measurements with 1.8% basic accuracy Resolution up to 0.01A and 0.1 V Measures AC current to 400 A Measures AC volts to 600 V Resistance measurement to 400 Ω Continuity for quick checking of shorts Automatic low battery indicator Display hold function Two year warranty What’s Included: (2) AAA Alkaline batteries Instruction card Safety information sheet Soft carrying case Test leads
  • The Fluke 1625 is intended for electrical utility or other high frequency environments as it has extra versatility for more demanding applications. The Fluke 1625 is a distinctive earth ground tester that can perform all four types of earth ground measurement. Not only measure ground resistance using the classic ‘fall of potential test’ but also enable time saving testing using the ‘selective’ and ‘stakeless’ methods.  ‘Selective’ testing does not require the electrode under test to be disconnected during the measurement, thus increasing safety.  The simple ‘stakeless’ method quickly checks ground connections using two current transformers (probes) clamped around the ground conductor under test. Testing Methods
    • 3- and 4-Pole Fall of Potential – standard earth ground testing using two ground stakes
    • 4-Pole Soil Resistivity testing – determine soil resistivity using four ground stakes
    • Selective testing – without disconnecting ground rods, a technician can measure ground resistance using a combination of stakes and a clamp.
    • Stakeless testing – innovative solution using only clamps, instead of ground stakes, to measure earth ground loop resistance.
    The Fluke 1625 offers these advanced features:
    • Automatic Frequency Control (AFC) – identifies existing interference and chooses a measurement frequency to minimize its effect, providing a more accurate earth ground value.
    • R* measurement – calculates earth ground impedance at 55 Hz to more accurately reflect the earth ground resistance that a fault-to-earth ground would see.
    • Adjustable limits – for quick test result verification.
    Earth ground resistance and soil resistivity should be measured when:
    • Designing earth ground systems
    • Installing new ground system and electrical equipment
    • Periodically testing ground and lightning protection systems
    • Installing large electrical equipment such as transformers, switchgears, machines, etc.
    The Fluke 1625 is the stand-alone unit For a basic model see the Fluke 1623 What’s Included:
    • Fluke 1625 tester
    • 2 test leads
    • 2 alligator clips
    • 4 earth ground stakes
    • 3 cable reels with wire (2-25 m, 1-50 m)
    • selective/stakeless clamp set (one inducing, one sensing)
    • Batteries
    • Users manual
    • Rugged carrying case
  • The Fluke 1621 earth ground tester is an easy-to-use earth ground tester. For ground resistance testing, the 1621 is the first line of defense in detecting reliable ground connections. The unit features basic ground testing methods including 3-pole Fall-of-Potential as well as 2-pole ground resistance tests. Its convenient size, rugged holster, and large, clear LCD display make it an ideal field earth ground tester, for most electrical grounding work environments. With a simple user interface and intuitive functionality, the Fluke 1621 is a handy grounding tool for electrical contractors, utility test engineers, and earth ground specialists. What’s Included:
    • Fluke 1621 Tester
    • 2 cable reels with wire (1-50m, 1-25m)
    • 3 earth ground stakes
    • 1 Test lead (red and black 2m)
    • 2 Alligator Clips
    • Batteries
    • Users manual
    • Hard carrying case
  • Feel free to contact us: Mobile: 0344 3813810 Versatile meter for maintenance, field service and bench repair. The Fluke 179 True-rms digital multimeter has the features needed to find most electrical and HVAC problems. Simple to use with significant improvements like True-rms, frequency, capacitance, temperature and min-max record. The Fluke 179 has more measurement functions, conformance to the latest safety standards, and a much larger display that’s easier to view. Check the features and specifications using the tabs above. Electrical safety All inputs are protected to measurement CAT III 1000 V and CAT IV 600V. This meter can withstand transient impulses in excess of 8000 V to help protect you from arc blasts resulting from surges and spikes. Available as kits such as: Fluke 179/1AC-IIElectrician’s Multimeter and Voltage Tester Combo Kit or Fluke 179/61 Industrial Multimeter and Infrared Thermometer Combo Kit or Fluke 179/TPAK Digital Multimeter & ToolPak™ Combo Kit Also available with no temperature asFluke 177or as Fluke 175 Combo Kit includes:
    • Fluke 179 True-rms Digital Multimeter
    • Fluke 80BK K-type temperature probe
    • Fluke AC280 SureGrip Heavy Duty Hook Clips
    • Fluke TP910 Electronic Test Probes
    • Fluke TL224 SureGrip Silicone Test Leads resist heat
    • Fluke TPAK ToolPak meter hanging accessory to hold meter to steel surfaces
    • NEW! Fluke C35 lightweight soft case to provide optimal protection and storage
    What’s Included:
    • Fluke 179 True-rms Digital Multimeter
    • Fluke 80BK K-type temperature probe
    • Fluke AC280 SureGrip Heavy Duty Hook Clips
    • Fluke TL910 Electronic Test Probes
    • Fluke TL224 SureGrip Silicone Test Leads resist heat
    • Fluke TPAK ToolPak meter hanging accessory to hold meter to steel surfaces
    • NEW! Fluke C35 lightweight soft case to provide optimal protection and storage
    The Fluke 1621 earth ground tester is an easy-to-use earth ground tester. For ground resistance testing, the 1621 is the first line of defense in detecting reliable ground connections. The unit features basic ground testing methods including 3-pole Fall-of-Potential as well as 2-pole ground resistance tests. Its convenient size, rugged holster, and large, clear LCD display make it an ideal field earth ground tester, for most electrical grounding work environments. With a simple user interface and intuitive functionality, the Fluke 1621 is a handy grounding tool for electrical contractors, utility test engineers, and earth ground specialists. What’s Included:
    • Fluke 1621 Tester
    • 2 cable reels with wire (1-50m, 1-25m)
    • 3 earth ground stakes
    • 1 Test lead (red and black 2m)
    • 2 Alligator Clips
    • Batteries
    • Users manual
    • Hard carrying case
  • Feel free to contact us: Mobile: 0344 3813810
    The Fluke 87V offers accuracy and diagnostics for maximum industrial productivity in the tool box or on the bench. The Fluke 87V multimeter has improved measurement functions, troubleshooting features, resolution and accuracy to solve more problems on motor drives, in plant automation, power distribution, and electromechanical equipment. With its newly incorporated selectable low pass filter, the Fluke 87V allows troubleshooters to take accurate voltage, current and frequency measurements on the output side of the drive at either the drive itself or the motor terminals. The Fluke 87V/E2 Industrial Electrician Combo Kit makes troubleshooting more productive with standard meter hanging accessory for handsfree operation, soft case for protection and storage, 1.5 m heat resistant silicone test leads and more. Features for maximum productivity
    • Unique function for accurate voltage and frequency measurements on adjustable speed motor drives and other electrically noisy equipment
    •  Built-in thermometer conveniently allows you to take temperature readings without having to carry a separate instrument
    •  Large digit display with bright, two-level backlight
    Electrical safety All inputs are protected to Category III, 1000 V and Category IV 600 V. They can withstand impulses in excess of 8,000 V and reduce risks related to surges and spikes. See the Fluke 87V – Industrial True-rms Multimeter with Temperature Also available in an average responding multimeter, Fluke 83V What’s Included:
    • Fluke 87V Industrial Multimeter
    • Fluke AC220 retractable long reach alligator clips
    • Fluke C35 lightweight soft case to provide optimal protection and storage
    • Fluke TPAK ToolPak meter haning accessory to hold meter to steel surfaces
    • Fluke TL224 1.5 m silicone leads resist head
    • Fluke TP238 removable probes with 4 mm of exposed metal to use on industrial circuits
    • 9V battery (installed)
    • Getting Started Manual
    • CD with detailed manual
    • Fluke 80BK K-type temperature probe
  • Feel free to contact us: Mobile: 0344 3813810
    A complete automotive diagnostic package with everything you need in an automotive multimeter The new Fluke 88V has improved measurement functions, troubleshooting features and accuracy to solve more problems on conventional and hybrid vehicles. The 88V is made in the U.S.A. and carries the industry leading lifetime warranty. The Fluke 88V operates very similar to the classic Fluke 88, but with more problem solving power, safety, convenience and impact protection. Combo Kit Includes: 88V multimeter, TL224 silicone test leads, AC285 long reach alligator clips, TP220 test probes, RPM 80 inductive RPM pick-up, magnet and strap, 80BK temperature probe, two automotive backprobe pins, insulation piercing probe, C800 durable carrying case, holster, 9V battery (installed), Getting Started Manual, and CD with detailed manual. The new 88V is independently tested to comply with the 2nd edition of ANSI/ISA S82.01 and EN61010-1 CAT IV 600V/CAT III 1000V. They can withstand impulses in excess of 8,000 V and reduce risks related to surges and spikes. What’s Included:
    • Fluke 88V Automotive Multimeter
    • Fluke TL224 Heat Resistant Silicone Test Leads
    • Fluke TP220 Removable Sharp Point Test Probes
    • Fluke AC285 Large Jaw Alligator Clips
    • Fluke TPAK Magnetic Hanger
    • Fluke 80BK Temperature Probe
    • Fluke RPM80 Inductive Pick-up
    • Automotive Backprobe Pins
    • Insulation Piercing Probe
    • Packaged in a durable carrying case (Fluke C800)
  • Feel free to contact us: Mobile: 0344 3813810
    For the complete solution to HVAC troubleshooting the extra value-packed HVAC Technician’s Combo Kit, provides the ability to troubleshoot and solve problems more efficiently by providing all the needed accessories an HVAC professional would need in a compact carry case. 3-year product warranty on Fluke-116 DMM, 2-year warranty on Fluke-62 IR Thermometer and 1-year warranty on accessories What’s Included:
    • Fluke 116 HVAC Multimeter with Temperature and Microamps
    • Fluke 62 Infrared Thermometer
    • Fluke TL75 Hard Point Test Lead Set
    • Fluke TPak ToolPak Magnetic Meter Hanging Strap
    • NEW! Fluke C115 Deluxe carrying case with shoulder strap
    • Fluke 80BK Integrated Temperature Probe
    • Fluke 80AK Thermocouple Adapter
    • NEW! Fluke 80PK-11 Pipe Wrap Thermocouple
  • Feel free to contact us: Mobile: 0344 3813810
    This combo kit pairs the new Fluke 117 DMM with a Fluke 322 clamp meter for productive and effective troubleshooting in one total solution, including the new C115 durable soft carrying case for protection and easy meter transportation. 3 years warranty on Fluke 117 DMM, 2 years warranty on Fluke 322 Clamp meter and 1 year on accessories. What’s Included:
    • Fluke 117 True-rms Digital Multimeter with non-contact voltage detector
    • NEW! Fluke C115 Deluxe carrying case with shoulder strap
    • Fluke 322 Compact Clamp Meter
    • Fluke TL75 Hard Point Test Lead Set
    • Fluke TPAK ToolPak Magnetic Meter Hanging Kit
  • Feel free to contact us: Mobile: 0344 3813810
    The Fluke 189 is the most advanced meter with features, precision and accuracy to troubleshoot industrial and electronic equipment in the field or on the bench. The Fluke 189 has a built-in data logger to record measurements unattended.  Recorded data can be viewed on the 189 or transferred to a PC with optional FlukeView Forms software.
    • Built in data logger records reading and time to catch intermittent problems
    • Measure 20 A for up to 30 seconds, 10 A continuous
    • Temperature, capacitance, dB, frequency, pulse width and duty cycle to find more problems with one tool
    • Large bright white display with dual parameter
    • Isolated IR communication port to send data to a PC
    • Premium test leads (Fluke TL71) and alligator clips (Fluke AC72) included
    • New! USB data cable with FlukeView Forms
    • New! battery pack (Fluke BP189) extends battery life to over 400 hours
    The Fluke 189 Data Logging Multimeter and Software Combo Pack provides a practical, affordable approach to achieve significantly improved maintenance performance. With the flexibility to monitor more than 20 different electrical functions plus temperature, it can help you increase your team’s productivity and reduce downtime by helping you find your problems faster. Flukeview Forms Software (included in Combo Pack) allows overlaying of data from six different meters or time periods to find cause-effect relationships or for predictive maintenance applications. Electrical safety All inputs are protected to measurement CAT III 1000 V and CAT IV 600 V. Available in non-logging version as Fluke 187 or just get the multimeter on its own Fluke 189 What’s Included:
    • Logging Multimeter  (Fluke 189)
    • FlukeView® Forms Software  (Fluke FVF-SC2)
    • USB Cable adapter  (IR189USB)
    • Test Lead Set  (Fluke TL71)
    • Alligator Clip Set  (Fluke AC72)
    • Temperature Thermocouple  (Fluke 80BK)
    • High Capacity Battery Pack  (Fluke BP189)
    • Soft Carrying Case  (Fluke C25)
    • Meter Hanging Kit  (Fluke TPAK)
  • Feel free to contact us: Mobile: 0344 3813810
    Maximize productivity with the combined Fluke 287 and FlukeView forms combo kit. Designed for today’s professionals involved in the R & D, maintenance, manufacture and design of electronic circuits or systems. With built-in data logger and TrendCapture (the meters on screen graphical display) cabability,  the 287 helps you track down elusive, intermittent problems or monitor equipment with any of its functions. FlukeView Forms enables you to document, store, and analyze individual readings or series of measurements, overlay logged data to find cause and effect relationships, or turn your data into meaningful graphs and tables for a professional report. The 287/FVF combo kit gives you a practical and affordable approach to documenting circuit design performance. What’s Included:
    • Fluke-287 True-rms Electronic Logging Multimeter with TrendCapture
    • FlukeView Forms Software and cable
    • 80BK-A Thermocouple Probe
    • CAT III 1000 V 10 A Modular test leads (red, black)
    • CAT III 1000 V 10 A Modular test probes (red, black)
    • CAT II 300 V 5 A Alligator Clips (red, black)
    • C280 Soft Case for meter protection and accessory storage
  • Feel free to contact us: Mobile: 0344 3813810
    The Fluke 2AC is the latest addition to the VoltAlert™ ac non- contact voltage tester family from Fluke and is designed to be pocket-sized and easy to use. The 2AC tests for energized circuits and defective grounds, whether it’s for an electrician on the factory floor or the do-it-yourselfer around the house. The tip of the pocket-sized tester will glow red when within close proximity of an outlet, terminal strip, or power cord where voltage is present.
    • Voltage detection from 90 to 1000 V ac, suitable for a wide range of residential, commercial and industrial needs.
    • NEW! Always on, using special low power circuitry to sustain battery life and ensure your 2AC is always ready.
    • NEW! Innovative ‘Battery Check’ button function ensures battery is in good condition*
    • Category IV – 1000 V overvoltage rated product for best in class user protection
    • Integrated clip design, optimized for pocket storage
    • Powered by 2x AAA batteries (included)
    • Fluke ruggedness and reliability
    • Two-year warranty
  • Feel free to contact us: Mobile: 0344 3813810
    Electrical tester with OpenJawTM Current The Fluke T5-1000 Electrical Tester lets you check voltage, continuity and current with one compact tool. With the T5-1000, all you have to do is select volts, ohms, or current and the tester does the rest. The OpenJawcurrent lets you check current up to 100A – without breaking the circuit. Its tough test leads stow neatly in the back of the tester, making it easy to tote the T5-600 in your tool pouch. Detachable SlimReachtest probes are customized for national electrical standards. The test leads accept optional accessories such as clips and specialty probes. The optional H5 holster lets you clip the T5 onto your belt. Also available in 600V – see the Fluke T5-600 Voltage, Continuity and Current Tester
  • Feel free to contact us: Mobile: 0344 3813810
    Has your solenoid tester ever over-heated, melted, burned out, or worse? The new, full-featured Fluke T+PRO Electrical Tester offers all the advantages of a traditional solenoid tester, with added functionality, but none of the typical drawbacks. The Fluke T+PRO Electrical Tester is the ideal, full-featured tester for the demanding commercial and industrial electrician.  With voltage measurement, continuity, built-in flashlights, GFCI trip capability, and Fluke’s legendary ruggedness and reliability, the tester is an excellent choice for most residential, commercial, and industrial applications. The Fluke T+PRO Electrical Tester comes with a rotary field indicator for troubleshooting three-phase systems, resistance measurement to 9.99 KOhms, as well as a backlit LCD display for easier viewing. The Fluke T+PRO helps electricians comply with NPFA 70E Article 110.9 (A), which states that “Test equipment … shall be rated for circuits and equipment to which they will be connected. The T+PRO Electrical Tester carries a CAT IV 600 V and CAT III 1000 V rating, appropriate for most environments where electricians work. Applications:
    • Industrial electricians, commercial electricians, particularly those who work on low-voltage lighting.
    • Front-line electrical troubleshooting
    • AC/DC voltage measurement
    • Continuity testing
    • Testing GFCI circuits
    • Resistance measurement
    • Checking the rotation of electrical motors
    • Checking the proper set up of 3-phase systems
    • Troubleshooting low-voltage lighting
    What’s Included:
    • User manual
    • Test lead wrap
    • Fluke TP2 test probes
    • 2 AAA batteries
  • Feel free to contact us: Mobile: 0344 3813810
    The pocket-sized voltage detector The next generation VoltAlert™ AC non-contact voltage testers from Fluke are easy to use — just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there’s voltage present. Electricians, maintenance, service, safety personnel, and homeowners can quickly test for energized circuits in the workplace or at home. A must for safe practices around electricity.
  • Feel free to contact us: Mobile: 0344 3813810 The industrial meter for demanding users. New diagnostic functionality for maximizing productivity in the plant. The new Fluke 289 True-RMS Industrial Logging Multimeter with TrendCapture is the next generation high performance industrial logging multimeter designed to solve complex problems in electronics, plant automation, power distribution, and electro-mechanical equipment. With the ability to log data and review it graphically on-screen, you can solve problems faster and help minimize downtime. Let the new 289 be your watchdog for systems or processes while you are off solving other problems. Be sure to also check out the Fluke 287 True-RMS Electronics Logging Multimeter with TrendCapture designed for electronics professionals or the Fluke 289 and Fluke i400 Clamp Meter Combo Kit APPLICATIONS:
    • Install or maintaining electronic machinery/plant equipment
    • Testing adjustable speed motor drives
    • Log and record results
    • In-plant automation applications
    • Power distribution
    • Electro-mechanical equipment service
    • Industrial electronics
    What’s Included:
    • Manual
    • 6 AA Batteries, installed
    • TL71 Silicone Test Leads
    • Probe Holder
    • Two AC72 Alligator Clips
    Supplemental Material:
    • Registration Card
    • Cal Practices Document
    • CD-ROM Users’ Manual (16 languages)
    • Getting Started Manual
    • Calibration Certification Sheet
  • Feel free to contact us: Mobile: 0344 3813810
    The Fluke 87V offers accuracy and diagnostics for maximum industrial productivity in the tool box or on the bench. The Fluke 87V multimeter has improved measurement functions, troubleshooting features, resolution and accuracy to solve more problems on motor drives, in plant automation, power distribution, and electromechanical equipment. With its newly incorporated selectable low pass filter, the Fluke 87V allows troubleshooters to take accurate voltage, current and frequency measurements on the output side of the drive at either the drive itself or the motor terminals. Features for maximum productivity
    • Unique function for accurate voltage and frequency measurements on adjustable speed motor drives and other electrically noisy equipment
    • Built-in thermometer conveniently allows you to take temperature readings without having to carry a separate instrument
    • Large digit display with bright, two-level backlight
    Electrical safety All inputs are protected to Category III, 1000 V and Category IV 600 V. They can withstand impulses in excess of 8,000 V and reduce risks related to surges and spikes. For a greater value see the Fluke 87V/E2 – Industrial Electrician’s Combo Kit or the Fluke 87V/AEK – Advanced Electronic Kit or the Fluke 87V/IMSK – 87V with i400 Clamp Meter Combo Kit Also available in an average responding multimeter, Fluke 83V What’s Included:
    • Fluke TL75 test leads
    • Fluke AC72 Alligator Clips
    • Holster
    • 9V battery (installed)
    • Getting Started Manual
    • CD with detailed manual
    • Fluke 80BK temperature probe
  • Feel free to contact us: Mobile: 0344 3813810 The Fluke 28-II multimeter is the new standard for rugged Fluke 28 II digital multimeter defines a new standard for operating in harsh conditions with the features and accuracy to troubleshoot most electrical problems. Fluke 28-II has an IP 67 (waterproof and dustproof) rating, MSHA approvals (pending), extended operating temperature range of -15 °C to +55 °C (5 °F to 131 °F, -40 °C for up to 20 minutes) and 95 % humidity, and have been designed and tested to withstand a 3 m (10 ft) drop. This meter is built to work in the toughest environments.
    • Measure up to 1000 V ac and dc
    • Measure up to 10 A (20 A for 30 seconds)10,000 μF capacitance range
    • Frequency to 200 kHz
    • Extended ac voltage bandwidth – 40 Hz to 30 kHz
    • Resistance, continuity and diode test
    • Min/Max and average recording to capture variations automatically
    • Peak min-max
    • Unique function for accurate voltage and frequency measurements on adjustable speed motor drives and other electrically noisy equipment
    • IP 67 waterproof & dustproof protection, completely sealed for use in harsh environments
    • Designed to withstand 3 meter drop (with holster)
    • True-rms ac voltage and current for accurate measurements on non-linear loads
    • Hi resolution 20,000 count display mode
    • Backlit keypad buttons allow for easy visibility in lowlit areas
    • Large display digits and 2 level bright white backlight for increased visibility
    • Reversible holster for added protection when not in use
    • Withstands hazardous 8,000 volt spikes caused by load switching and faults on industrial circuits and complies with second edition IEC and ANSI electrical safety standards
    • Long battery life (800 hours)
    • Relative mode to remove test lead resistance from low ohms measurements
    • Auto and manual ranging for maximum flexibility
    • Optional magnetic hanger for easy setup and viewing while freeing your hands for other tasks
    • MSHA approval (pending)
  • Feel free to contact us: Mobile: 0344 3813810 The new standard for rugged Fluke 27 II and Fluke 28 II digital multimeters define a new standard for operating in harsh conditions with the features and accuracy to troubleshoot most electrical problems. Both meters have IP 67 (waterproof and dustproof) rating, MSHA approvals (pending), extended operating temperature range of -15 °C to +55 °C (5 °F to 131 °F, -40 °C for up to 20 minutes) and 95 % humidity, and have been designed and tested to withstand a 3 m (10 ft) drop. The new Fluke 20 Series Multimeters are built to work in the toughest environments.
    • Measure up to 1000 V ac and dc
    • Measure up to 10 A (20 A for 30 seconds)10,000 μF capacitance range
    • Frequency to 200 kHz
    • Extended ac voltage bandwidth – 40 Hz to 30 kHz
    • Resistance, continuity and diode test
    • Min/Max and average recording to capture variations automatically
    • IP 67 waterproof & dustproof protection, completely sealed for use in harsh environments
    • Designed to withstand 3 meter drop (with holster)
    • Average responding voltage and current for measurements (Fluke 28-II is TRMS)
    • Backlit keypad buttons allow for easy visibility in lowlit areas
    • Large display digits and 2 level bright white backlight for increased visibility
    • Reversible holster for added protection when not in use
    • Withstands hazardous 8,000 volt spikes caused by load switching and faults on industrial circuits and complies with second edition IEC and ANSI electrical safety standards
    • Long battery life (800 hours)
    • Relative mode to remove test lead resistance from low ohms measurements
    • Auto and manual ranging for maximum flexibility
    • Optional magnetic hanger for easy setup and viewing while freeing your hands for other tasks
    • MSHA approval (pending)
    Note: for a TRMS version of this Fluke 27-II that also includes built-in temperature measurement and a unique Low Pass filter for measuring accurate readings when working on variable speed drives (VFDs/VSDs) see the Fluke 28-II industrial multimeter.
  • Feel free to contact us: Mobile: 0344 3813810 The Fluke 8845A Bench Top 6.5 digit Precision Multimeter has the precision and versatility to handle your most demanding measurements, on the bench or in a system. These meters are both high performance and feature rich, yet also remarkably easy to use. The Fluke 8845A Bench Top 6.5 digit Precision Multimeter performs the functions you would expect to see in a multifunction DMM, including measuring volts, ohms, and amps. Basic V dc accuracy of up to 0.0024 %, 10 A current range, and a wide ohms range give you an unbeatable combination of measurement capability. You can also use the the Fluke 8845A Bench Top 6.5 digit Precision Multimeter to measure frequency and period.  The functions of a counter, capacitance meter, and thermometer are built in for unparalleled versatility. Extend the meters’ utility even more with their graphical display modes, including Trendplot paperless recorder mode, statistics and histograms—features you won’t find on other multimeters. Of course, the meter is also durable and dependable, features you expect from any Fluke meter. This unique combination of features and performance makes the Fluke 8845A Bench Top 6.5 digit Precision Multimeter an unbeatable value for a wide variety of applications, including manufacturing test, research and development, and service. What’s Included:
    • TL71 Test Lead Set, Premium DMM
    • LCI Line Core
    • Spare Line Power Fuse
    • Statement of Calibration Practices
    • WEEE Information Sheet
    • Warranty Information
    • Programmer, Users and Service Manuals (CD-ROM)
    • FlukeView Forms – Basic for 8845/8846
  • Feel free to contact us: Mobile: 0344 3813810 Versatile multimeter for manufacturing, development and service applications
    • 5.5 digit resolution
    • Basic V dc accuracy of 0.01 %
    • Dual display
    • Dedicated dc leakage current measurement
    • 2×4 ohms 4-wire measurement technique
    • Six dedicated buttons for fast access to instrument setups
    • Hi/Lo limit compare for Pass/Fail testing
    The Fluke 8808A multimeter has a broad range of functions, measuring volts, ohms and amps with a basic V dc accuracy of 0.01 %. It is remarkably easy to use, even by unskilled operators, because it makes the measurements you perform most often extremely easy and fast to do. Six setup buttons on the Fluke 8808A front panel operate like a car radio’s station presets. Simply set up the meter for a common measurement, then press shift followed by a setup button (S1 to S6) to save the setup. Now each time you perform that measurement, you simply press the appropriate setup key. It’s that easy! The setup buttons eliminate the need to follow complex work instruction sheets. Operators no longer need to press multiple buttons to set up a measurement function and range, test limits, or enter other parameters to make a measurement. What’s Included:
    • Meter
    • TL71 test leads
    • Line cord
    • Spare line fuse
    • Statement of cal practices
    • WEEE information sheet
    • Warranty statement
    • Getting Started guide (English, French, German, Spanish, Italian, Simplified Chinese, Japanese)
    • CD Rom with user manual (English)
  • Feel free to contact us: Mobile: 0344 3813810 The NEW Fluke 233 True-rms Remote Display Digital Multimeter gives you ultimate flexibility in unusual measurement scenarios. Place the removable display where you can see it and then put the meter where it is convenient for you—no more juggling of leads and the meter while stretching into a tight spot. You can now take measurements in hard-to-reach places, where machines or panels are physically separated from a limit or isolator switch, or in user prohibited areas such as clean rooms or hazardous areas. Imagine the possibilities! What would you do if you could be in two places at once?
    • True-rms ac voltage and current for accurate measurements on non-linear signals
    • Measure up to 1000 V ac and dc
    • Measure up to 10 A (20 A for 30 seconds)
    • 10,000 μF capacitance range
    • Frequency to 50 kHz
    • Built in thermometer conveniently allows you to take temperature readings without having to carry a separate instrument
    • Resistance, continuity and diode test
    • Low power wireless technology allows the display to be carried up to 10 meters (33 ft) away from the point of measurement for added flexibility. No interference with measurements
    • The removable magnetic display can be conveniently mounted where it is easily seen
    • Make measurements without holding the meter to improve visual focus on probes and augment safe electrical measurements
    • Use as a conventional multimeter when the display is connected
    • Radio transmitter automatically turns off when the display is connected to the meter
    • Auto power off maximizes battery life
    • Min/Max and Average recording to capture variations automatically
    • Test continuity and diodes
    • Easy to read display with large digits and bright backlight
    • Battery life approximately 400 hours
  • Feel free to contact us: Mobile: 0344 3813810 Two powerful tools in one The Fluke 1577 Insulation Multimeter combine a digital 1 kV insulation tester with a full-featured, true-rms digital multimeter in a single, compact, handheld unit, which provides maximum versatility for both troubleshooting and preventative maintenance. Whether you work on motors, generators, cables, or switch gear, the Fluke 1577 Insulation Multimeter is ideally suited to help you with your tasks. For a greater capabilities purchase the Fluke 1587 Insulation Multimeter What’s Included:
    • Remote probe
    • Test leads
    • Alligator clips
    • Hard case
    • User documentation
  • Feel free to contact us: Mobile: 0344 3813810
    The Fluke 787 Process Meter was the first tool to combine a loop calibrator with a fully-functional 1000V True RMS digital multimeter to give process technicians double the power in one tool. A maintenance and calibration tool that will be at home in every instrumentation technician’s tool box, the Fluke 787 Process Meter combines a DMM and a Loop Calibrator in one rugged, handheld tool, for about what you would expect to pay for a loop calibrator alone. Based on the trusted Fluke 87 DMM, the Fluke 787 adds the ability to measure, source, and simulate dc loop current with 0.05% accuracy and 1 microamp resolution. Put it all together and you have the ideal tool for troubleshooting and calibrating current loop applications. So if you’re tired of always tracking down a calibrator, lugging around two tools and switching back and forth, get the single best solution for doubling your power – the Fluke 787 ProcessMeter. Also see the Fluke 789 ProcessMeter What’s Included:
    • Alligator Clips
    • Protective Yellow Holster with test lead storage
    • One 9V alkaline battery
    • Fluke TL75 Safety-Designed Test lead Set
    • Product over and Users Manual (CD-ROM) in 14 languages
  • Feel free to contact us: Mobile: 0344 3813810 The Fluke 287 True-rms Electronics Logging Multimeter with TrendCapture quickly documents design performance and graphically displays what happened. Its’ unique logging and graphing capabilities mean you no longer need to download logged readings to a PC to detect a trend. The Fluke 287 True-rms Electronics Logging Multimeter with TrendCapture packs more accuracy and convenience into a handheld multimeter than ever before, putting more problem solving power in your hands. It is the ultimate handheld tool for demanding applications that require high-precision APPLICATIONS:
    • Develop, install, or maintain electronic devices
    • Precision testing of surface mount and high density circuits
    • Customers who need to log and record results to solve intermittent problems
    • Communication; wireless, wired, LAN, broadband, CATV, audio/video
    • Industrial / Electrical equipment
    • Instrumentation (example: test and medical equipment)
    • Consumer electronics
    • Automotive
    • Education
    • Security
    What’s Included:
    • Manual
    • 6 AA Batteries, installed
    • TL71 Silicone Test Leads
    • Probe Holder
    • Two AC72 Alligator Clips
    Supplemental Material:
    • Registration Card
    • Cal Practices Document
    • CD-ROM Users’ Manual (16 languages)
    • Getting Started Manual
    • Calibration Certification Sheet
  • Feel free to contact us: Mobile: 0344 3813810
    Designed by electricians. Engineered by Fluke. Compact true-rms meter for commercial applications. The Fluke 117 is the ideal meter for demanding settings like commercial buildings, hospitals and schools. The 117 includes integrated non-contact voltage detection to help get the job done faster. The Fluke 117 has dual impedance capability: incorporating both regular high impedance test capabilities and low impedance functions for detecting ghost voltages, just switch to the Auto-V/LoZ (low impedance) test setting to whether measurement is a ghost voltage.
    • Auto-V stands for automatic volts. This feature automatically determines whether the measured signal is ac voltage or dc voltage, selects the correct function and range, and displays the correct information.
    • LoZ stands for Low Impedance (Z). This feature presents a low impedance input to the circuit under test. This reduces the possibility of false readings due to ghost voltages and improves accuracy when testing to determine absence or presence of voltage.
    The Fluke 117 also includes the built-in VoltAlert non-contact voltage function.  Located on the top of the meter above the LCD display, it’s another feature handy for detecting the invisible. The VoltAlert function detects the presence of ac voltage, sounds an audible tone and activates a red LED indicator light on the top center of the LCD display.  Using this feature before making a contact measurement can add an extra layer of safety. Also check out the Fluke 114 Electrical Multimeter, the Fluke 115 Multimeter, and the Fluke 116 HVAC Multimeter with Temperature and Microamps. What’s Included:
    • 4 mm silicone test lead set
    • Holster
    • User manual
  • Feel free to contact us: Mobile: 0344 3813810
    Designed by electricians. Engineered by Fluke. The Fluke 116 HVAC Multimeter features temperature and microamps measurements useful for heating, ventilation, air conditioning and refrigeration (HVAC/R) technicians.  The Fluke 116 is a compact true-rms meter and has everything needed in an HVAC meter including temperature and microamp measurements to quickly troubleshoot problems with HVAC equipment and flame sensors. The Fluke 116 also, has dual impedance capability: incorporating both regular high impedance test capabilities and low impedance functions for detecting ghost voltages, just switch to the Auto-V/LoZ (low impedance) test setting to whether measurement is a ghost voltage.
    • Auto-V stands for automatic volts. This feature automatically determines whether the measured signal is ac voltage or dc voltage, selects the correct function and range, and displays the correct information.
    • LoZ stands for Low Impedance (Z). This feature presents a low impedance input to the circuit under test. This reduces the possibility of false readings due to ghost voltages and improves accuracy when testing to determine absence or presence of voltage.
    Also check out the Fluke 114 Electrical Multimeter, the Fluke 115 Multimeter, and the Fluke 117, the Electrician’s Multimeter with Non-contact voltage. What’s Included:
    • 4 mm silicone test lead set
    • 80BK Integrated Temperature probe
    • Holster
    • Installed 9 V battery
    • User manual
  • Feel free to contact us: Mobile: 0344 3813810 Designed by electricians. Engineered by Fluke. Compact true-rms meter for field service technicians. The Fluke 115 is the solution for a wide variety of electrical and electronic testing applications. Also check out the Fluke 114 Electrical Multimeter, the Fluke 116 HVAC Multimeter with Temperature and Microamps, and the Fluke 117, the Electrician’s Multimeter with Non-contact voltage.
  • Feel free to contact us: Mobile: 0344 3813810 Designed by electricians. Engineered by Fluke. Compact true-rms meter for electrical troubleshooting.  The Fluke 114 is a battery-powered, true-rms multimeter the perfect troubleshooting tool for “go/no-go” testing.  It includes a feature to prevent false readings caused by ghost voltage. Also check out the Fluke 115 Multimeter, the Fluke 116 HVAC Multimeter with Temperature and Microamps, and the Fluke 117, the Electrician’s Multimeter with Non-contact voltage. What’s Included:
    • Holster
    • Installed 9 V battery
    • Test leads
    • User manual
  • Feel free to contact us: Mobile: 0344 3813810 True-rms Basic Multimeter designed for basic electrical testsThe Fluke 113 Basic Multimeter gives utility users the means to quickly and easily do basic meter set and reconnect testing. This meter is simple-to-use and has the features needed to repair most electrical problems. The Fluke 113 Basic Multimeter has significant improvements over Fluke’s original 7-600, and other utility multimeters. Using the Fluke VCHEK™ LoZ low impedance measurement function, users can simultaneously test for voltage or continuity. The Fluke 113 Basic Multimeter can perform diode tests, and also provides both auto and manual ranging capabilities. With features such as conformance to the latest safety standards, backlight, and a much larger display that’s easier to view, this new meter is a must have for the utility users toolbox. What’s Included:
    • Fluke TL75 test leads
    • Holster
    • Users manual
    • and 9 V battery (installed).
  • Feel free to contact us: Mobile: 0344 3813810
    The Fluke 87V offers accuracy and diagnostics for maximum industrial productivity in the tool box or on the bench. The Fluke 87V multimeter has improved measurement functions, troubleshooting features, resolution and accuracy to solve more problems on motor drives, in plant automation, power distribution, and electromechanical equipment. With its newly incorporated selectable low pass filter, the Fluke 87V allows troubleshooters to take accurate voltage, current and frequency measurements on the output side of the drive at either the drive itself or the motor terminals. Features for maximum productivity
    • Unique function for accurate voltage and frequency measurements on adjustable speed motor drives and other electrically noisy equipment
    • Built-in thermometer conveniently allows you to take temperature readings without having to carry a separate instrument
    • Large digit display with bright, two-level backlight
    Electrical safety All inputs are protected to Category III, 1000 V and Category IV 600 V. They can withstand impulses in excess of 8,000 V and reduce risks related to surges and spikes. For a greater value see the Fluke 87V/E2 – Industrial Electrician’s Combo Kit or the Fluke 87V/AEK – Advanced Electronic Kit or the Fluke 87V/IMSK – 87V with i400 Clamp Meter Combo Kit Also available in an average responding multimeter, Fluke 83V What’s Included:
    • Fluke TL75 test leads
    • Fluke AC72 Alligator Clips
    • Holster
    • 9V battery (installed)
    • Getting Started Manual
    • CD with detailed manual
    • Fluke 80BK temperature probe
  • Feel free to contact us: Mobile: 0344 3813810
    Versatile digital multimeter for maintenance, field service and bench repair. The NEW Fluke 77-IV digital multimeter has the features needed to repair most electrical and electronic problems. This meter is simple to use and has significant improvements with more measurement functions, conformance to the latest safety standards, and a much larger display that’s easier to view. The Fluke Model 77-IV is a battery-powered, average responding-rms indicating multimeter, with a 6000-count, 3 3/4-digit display, and a bar graph. Measures:
    • AC / DC voltage & current
    • Wide 1000 V measurement range
    • Average responding AC measurements
    • 0.3% accuracy
    • 10 Amps continuous (20A for 30 seconds)
    • Frequency and capacitance
    • Resistance and continuity
    • Diodes
    This multimeter meets the CAT III and CAT IV IEC 61010 standards. Look at the Fluke 73-III Digital Mulitimeter or the waterproof design Fluke 27-YEL Analog/Digital Multimeter What’s Included:
    • Fluke TL75 test leads
    • 9 V battery (installed)
    • Manual
  • Feel free to contact us: Mobile: 0344 3813810 Versatile meter for maintenance, field service and bench repair. The Fluke 175 True-rms digital multimeter has the features needed to find most electrical, electronic, electro-mechanical and heating and ventilation problems.  Simple to use with significant improvements like True-rms, frequency, capacitance and min-max record. Check the features and specifications using the tabs above. Electrical safety All inputs are protected to measurement CAT III 1000  V and CAT IV 600V.  This meter can withstand transient impulses in excess of 8000 V to help protect you from arc blasts resulting from surges and spikes. Want better accuracy and a backlight see the Fluke 177 Also available with temperature as Fluke 179
  • Feel free to contact us: Mobile: 0344 3813810
    Versatile meter for maintenance, field service and bench repair. The Fluke 179 True-rms digital multimeter has the features needed to find most electrical and HVAC problems. Simple to use with significant improvements like True-rms, frequency, capacitance, temperature and min-max record. The Fluke 179 has more measurement functions, conformance to the latest safety standards, and a much larger display with backlight that’s easier to view. Check the features and specifications using the tabs above. Electrical safety All inputs are protected to measurement CAT III 1000 V and CAT IV 600V. This meter can withstand transient impulses in excess of 8000 V to help protect you from arc blasts resulting from surges and spikes. For even greater value, the Fluke 179 is also available in the following kits: Fluke 179/EDA2 Electronics Multimeter and Deluxe Accessory Combo Kit or Fluke 179/1AC-II Electrician’s Multimeter and Voltage Tester Combo Kit or Fluke 179/61 Industrial Multimeter and Infrared Thermometer Combo Kit or Fluke 179/TPAK Digital Multimeter & ToolPak Combo Kit or Fluke 179/IMSK Digital Multimeter & Clamp Meter Combo Kit Also available with no temperature as Fluke 177 or as Fluke 175 What’s Included:
    • Fluke 80BK Temperature Probe
    • Fluke TL75 Test Leads
    • Installed 9V battery
    • Users manual
  • Feel free to contact us: Mobile: 0344 3813810 The Fluke 434/PWR power analyzer is the ideal tool for finding energy waste in commercial and factory buildings and equipment. Electricians, field service engineers and maintenance technicians can use this special edition instrument to conduct energy consumption studies and electrical load analysis, and to perform power quality logging and analysis according to EN 50160. Fluke’s 434/PWR is a complete three-phase troubleshooting tool that measures virtually every power system parameter: voltage, current, frequency, power, energy consumption, cos f or power factor, unbalance, and harmonics and inter-harmonics. The Fluke 434/PWR is an upgraded version of the popular 434 model. It now includes the previously optional logging feature, Inrush and Transients measurement functions. In addition, it includes four iFlex 430, flexible current probes and a new soft case. The bundled PowerLog software enables logged files to be downloaded and reports generated automatically (the standard voltage leads and clips are included).

    Load studies and energy assessments

    • Monitor maximum power demand over user-defined averaging periods
    • Demonstrate the benefit of efficiency improvements with energy consumption tests
    • Measure harmonic distortion caused by electronic loads
    • Analyze reliability problems by capturing voltage dips and swells from load switching

    Applications

    • Load studies – verify electrical system capacity before adding loads
    • Energy assessments – quantify energy consumption before and after improvements to justify energy saving devices
    • Frontline troubleshooting – quickly diagnose problems on‐screen to get your operation back online
    • Quality of service compliance – validate incoming power quality at the service entrance
    • Long‐term analysis – uncover hard‐to‐find or intermittent issues
    • Analyze reliability problems by capturing voltage dips and swells from load switching
    What’s Included:
    • i430-Flexipack 4 current clamps
    • 5 Test leads, 4 black, 1 green
    • 5 Alligator clips, 4 black, 1 green
    • BC430 Battery charger eliminator
    • Power Log Software
    • OC4USB Optical cable for USB
    • WC100 Color localization set
    • Getting Started (booklet)
    • User Manual (CD-ROM)
  • Feel free to contact us: Mobile: 0344 3813810 Record three-phase power quality and monitor for power quality disturbances with the new Fluke 1750 Three Phase Power Recorder and the Fluke Power Analyzer software. These power meters automatically record every power quality parameter and event, on every cycle – all the time. Never miss capturing a disturbance – with the exclusive threshold-free measurement system, it’s automatic. Capture every measurement, every event, on every cycle, all the time with the Fluke 1750 Three Phase Power Recorder. Unprecedented accuracy and resolution provide complete visibility into your distribution system. The recorder automatically detects, scales, and powers current probes without needing batteries. Requiring only single-lead voltage connections enables safe and quick setups. Once power is applied the instrument automatically begins recording and LEDs give you assurance that the recorder is powered up and signals are within range – no more uncertainty that data is being recorded. The Fluke 1750 Three Phase Power Quality Recorder has an exclusive capture algorithm which makes certain all events are captured without the tedious setups and blind spots associated with threshold driven equipment. The PDA wirelessly interfaces with the recorder, allowing quick setup and verification with waveform displays, meter screens, and phasor diagrams. The built-in wireless technology allows you to control multiple instruments from a distance easily, without the need for a laptop computer (laptops can also be used when desired). Applications: Long-term analysis: Uncover hard-to-find or intermittent issues Power quality surveys: Quantify power quality throughout a facility, documenting results with professional reports Quality of service compliance: Validate incoming power quality at the service entrance Semi-permanent monitoring: Monitor critical equipment, capturing power quality events to correlate with equipment malfunctions What’s Included:
    • 1750 aquisition unit
    • PDA wireless “front panel interface” and charger power plug adapters
    • 4 – 400A current probes (3140)
    • 5 Test leads and clips
    • SD memory card
    • Fluke Power View and Fluke Power Analyze software
    • Power cord with international plug set
    • Ethernet cable
    • Color localization set
    • Printed Getting Started manual
    • Product CD with software and user manual PDF
  • Feel free to contact us: Mobile: 0344 3813810
    The Fluke 1745 Three Phase Power Quality Logger is an advanced IP50 power quality logger with real-time LCD and five hours UPS for technicians who troubleshoot and analyze power quality issues. Capable of simultaneously logging up to 500 power parameters for up to 85 days and monitoring for events, this allows you to analyze power quality in detail and to correlate intermittent events, helping to identify the root cause of disturbances. The included PQ Log software quickly assesses the quality of power at the service entrance, substation, or at the load, according to the latest EN50160 standard. The Fluke 1745 Three Phase Power Quality Logger can not only measure the common power parameters but it also measures voltage and current harmonics, interharmonics, mains signaling, unbalance, and frequency. Apart from the Fluke 1745, the Fluke 1740 series includes two other power quality loggers: Fluke 1743 & Fluke 1743.
    • The Fluke 1743 is capable of measuring most common power parameters but cannot measure voltage and current harmonics, interharmonics, mains signaling, unbalance or frequency.
    • The Fluke 1744 is more similar to the 1743 and is a better solution if you need to measure what the 1743 is incapable of measuring.
    Applications:
    • Disturbance analysis – Uncover root cause of equipment malfunction for later mitigation and predictive maintenance
    • Quality of service compliance – Validate incoming power quality at the service entrance
    • Power quality studies – Assess baseline power quality to validate compatibility with critical systems before installation
    • Load studies – Verify electrical system capacity before adding loads
    • Energy and power quality assessment – Validate performance of facility improvements by quantifying energy consumption, power factor, and general power quality before and after improvements
    What’s Included:
    • 4 Flexible probes 15/150/1500/3000 A with 2 m cable
    • CD-ROM with PQ Log software
    • RS232 interface cable and RS232-USB adapter
    • Test leads for voltages and power supply
    • 4 black dolphin clips
    • Color localization kit
    • Carrying bag
    • Test certificate with measurement values
    • Printed English manual
    • Multi-language manual CD
  • Feel free to contact us: Mobile: 0344 3813810
    The Fluke 1740 Series three-phase power quality loggers are everyday power meters for technicians who troubleshoot and analyze power quality issues. Capable of simultaneously logging up to 500 power parameters for up to 85 days and monitoring for events, these power loggers help uncover intermittent and hard-to-find power quality issues. The Fluke 1744 is a powerful three-phase power quality logger capable of logging the most common power parameters you’ll need for power quality monitoring such as:
    • V, A, W, VA, VAR
    • Power Factor
    • Energy
    • Flicker
    • Voltage
    • THD
    • Harmonics, Interharmonics
    • Mains Signaling
    • Unbalance
    • Frequency
    Apart from the Fluke 1744, the Fluke 1740 series includes two other power quality loggers: Fluke 1743 & Fluke 1745.
    • The Fluke 1743 includes the same features as the Fluke 1743 but is not capable of measuring voltage and current harmonics, interharmonics, mains signaling, unbalance and frequency.
    • The Fluke 1745 includes the same features as the Fluke 1744 but features an IP50 environmental rating, a real-time LCD display and a 5 hour UPS which is great if you need to read more data at the meter and have a longer backup battery life where there’s less chance of it getting wet.
    The main difference between the 1744 and the other 2 models in the series, is the 1744 measure harmonics, unbalance or mains signaling but doesn’t have an LCD display and only has a 3 hour UPS. The included PQ Log software quickly assesses the quality of power at the service entrance, substation, or at the load, according to the latest EN50160 standard. Applications:
    • Disturbance analysis – Uncover root cause of equipment malfunction for later mitigation and predictive maintenance
    • Quality of service compliance – Validate incoming power quality at the service entrance
    • Power quality studies – Assess baseline power quality to validate compatibility with critical systems before installation
    • Load studies – Verify electrical system capacity before adding loads
    • Energy and power quality assessment – Validate performance of facility improvements by quantifying energy consumption, power factor, and general power quality before and after improvements
    What’s Included:
    • 4 Flexible probes 15/150/1500/3000 A with 2 m cable
    • CD-ROM with PQ Log software
    • RS232 interface cable and RS232-USB adapter
    • Test leads for voltages and power supply
    • 4 black dolphin clips
    • Color localization kit
    • Carrying bag
    • Test certificate with measurement values
    • Printed English manual
    • Multi-language manual CD
  • Feel free to contact us: Mobile: 0344 3813810 The Fluke 1740 Series three-phase power quality loggers are everyday power meters for technicians who troubleshoot and analyze power quality issues. Capable of simultaneously logging up to 500 power parameters for up to 85 days and monitoring for events, these power loggers help uncover intermittent and hard-to-find power quality issues. The Fluke 1743 is a powerful three-phase power quality logger capable of logging the most common power parameters you’ll need for power quality monitoring such as:
    • V, A, W, VA, VAR
    • Power Factor
    • Energy
    • Flicker
    • Voltage
    • THD
    Apart from the Fluke 1743, the Fluke 1740 series includes two other power quality loggers: Fluke 1744 & Fluke 1745.
    • The Fluke 1744 includes the same features as the Fluke 1743 but can measure voltage and current harmonics, interharmonics, mains signaling, unbalance and frequency.
    • The Fluke 1745 includes the same features as the Fluke 1744 but features an IP50 environmental rating, a real-time LCD display and a 5 hour UPS which is great if you need to read more data at the meter and have a longer backup battery life where there’s less chance of it getting wet.
    The main difference between the 1743 and the other 2 models in the series, is the 1743 does not measure harmonics, unbalance or mains signaling. If you need to require these measurements, we recommend looking at the higher models. Software: The included PQ Log software quickly assesses the quality of power at the service entrance, substation, or at the load, according to the latest EN50160 standard. Applications:
    • Disturbance analysis – Uncover root cause of equipment malfunction for later mitigation and predictive maintenance
    • Quality of service compliance – Validate incoming power quality at the service entrance
    • Power quality studies – Assess baseline power quality to validate compatibility with critical systems before installation
    • Load studies – Verify electrical system capacity before adding loads
    • Energy and power quality assessment – Validate performance of facility improvements by quantifying energy consumption, power factor, and general power quality before and after improvements
    What’s Included:
    • 4 Flexible probes 15/150/1500/3000 A with 2 m cable
    • CD-ROM with PQ Log software
    • RS232 interface cable and RS232-USB adapter
    • Test leads for voltages and power supply
    • 4 black dolphin clips
    • Color localization kit
    • Carrying bag
    • Test certificate with measurement values
    • Printed English manual
    • Multi-language manual CD
Go to Top